Industrial sites are not cleaned like offices. Oil builds up around machinery, fine dust settles on overhead structures, and floors carry slip risks that general cleaning methods can’t manage. If you manage a plant, workshop or processing facility, you need a contractor who understands both the cleaning task and the safety framework around it. This guide covers what industrial cleaning services Perth WA businesses typically need, the safety requirements that apply, and what to expect when a contractor arrives on site.
What Industrial Cleaning Services Perth WA Sites Typically Need
“Industrial cleaning” covers a range of tasks that differ by industry. A food processing plant, a metal fabrication workshop and a logistics depot each have different contaminants, hazards and cleaning priorities. Most scopes draw on the following core services.
Machinery degreasing
Oil, grease, coolant and process residue collect on machinery, guarding, floors and surrounding surfaces. Left alone, they create slip hazards, attract dust and make it harder to spot leaks or wear.
Degreasing usually involves:
- Applying a solvent or alkaline degreaser suited to the residue
- Agitating the surface with brushes or pads, or using steam or pressure washing where equipment allows
- Rinsing and recovering the run-off, rather than letting it enter drains
- Drying the area so floors are safe to walk on afterwards
Whether equipment can be cleaned while running depends on its design and your site rules. Most degreasing around moving parts requires machinery to be isolated and locked out first. This is a decision for your site’s maintenance and safety team, not the cleaner alone.
Dust extraction and fine dust control
Dust is one of the most underestimated industrial hazards. It affects air quality, equipment performance and, in some industries, fire and explosion risk. Sweeping with a broom or using compressed air can push fine particles back into the air, so industrial dust control relies on:
- Industrial vacuum systems with suitable filtration, such as HEPA where the dust type calls for it
- Cleaning from the top down, starting with beams, ducting, light fittings and ledges, then moving to floors
- Scheduled cleaning intervals so dust doesn’t build up on elevated surfaces
If your site produces combustible dust (for example from timber, grain or certain metals), the vacuum equipment and cleaning method need to be suitable for the specific dust hazard and any hazardous-area classification. WorkSafe WA guidance recommends appropriate vacuum or wet-cleaning methods rather than dry sweeping or compressed air. Have a competent safety professional assess ignition risks, dust accumulation and equipment suitability before selecting cleaning equipment. Do not assume that a standard HEPA-filtered vacuum is automatically suitable for combustible dust environments.
Floor, high-level and general area cleaning
Alongside machinery and dust work, industrial scopes often include:
- Ride-on or walk-behind scrubbing of concrete and sealed floors
- High-level cleaning of racking, roof structures and services
- Cleaning of amenities, lunchrooms and office areas attached to the site
- Removal of general and light industrial waste
For large production or storage environments, see our factory cleaning and warehouse cleaning pages for related services.
Safety Requirements for Industrial Cleaning in WA
Industrial cleaning is carried out in an environment where hazards already exist. Safety is therefore a core part of the service, not an add-on.
Work health and safety duties
Western Australia operates under the Work Health and Safety Act 2020 and the Work Health and Safety (General) Regulations 2022, which came into effect on 31 March 2022 and are administered by WorkSafe WA. Under this framework, businesses must ensure, so far as is reasonably practicable, the health and safety of workers and others affected by their work. This duty applies to both the site operator and the cleaning contractor, and where they share a workplace, they are expected to consult, cooperate and coordinate.
In practice, this means you should expect your contractor to discuss hazards with you before work starts, rather than simply turning up with equipment.
Risk assessments and safe work method statements
Before an industrial clean, a competent contractor will assess the tasks and the site. The outcome is usually documented as a risk assessment, and for higher-risk tasks a safe work method statement (SWMS) or equivalent procedure. These documents typically cover:
- The tasks to be performed and the equipment used
- Hazards such as slips, manual handling, noise, hazardous chemicals and dust
- Control measures, including isolation of machinery, exclusion zones and PPE
- Emergency procedures and who to contact
Under WA’s Work Health and Safety (General) Regulations 2022, a SWMS is legally required before high-risk construction work begins. This includes construction work involving a risk of a fall of more than 2 metres and construction work in or near a confined space, among other specified activities. Ordinary industrial cleaning does not automatically require a SWMS simply because it is high-risk industrial work. However, the contractor must still assess and manage workplace risks and prepare suitable safe work procedures and other documentation where appropriate.
Hazardous chemicals and safety data sheets
Degreasers and industrial detergents can be hazardous. Contractors should hold current safety data sheets (SDS) for the products they bring on site and should be able to show them on request. If your site has its own hazardous substances register, share it with the contractor so products don’t conflict with site processes or materials.
Confined spaces, heights and energy isolation
Some industrial cleaning tasks involve tanks, pits, silos, elevated work platforms or equipment with stored energy. These activities carry specific regulatory requirements, including permits, trained personnel and rescue arrangements. Not every cleaning contractor is set up to do this work, so check this early rather than assuming it falls within a standard scope.
Under WA’s WHS regulations, confined-space work requires appropriate risk assessment, entry permits, isolation and communication arrangements, suitable training and emergency rescue procedures. Work at height requires the risks of falls to be managed, with applicable fall-prevention and safety measures determined by the task and workplace. Certain activities, including operating specified elevating work platforms, scaffolding, cranes and forklifts, require the relevant high-risk work licence. Check the current regulations and site-specific requirements before undertaking these activities.
WorkSafe WA and Site Induction: What Actually Applies
Contractors often ask whether they need a “WorkSafe WA induction”. WorkSafe WA is the regulator. Site inductions are usually delivered by the person in control of the workplace, as part of their own safety management system.
A typical industrial site induction covers:
- Site layout, restricted areas and traffic management (forklifts, trucks, pedestrians)
- Emergency exits, assembly points and alarm procedures
- Required PPE, such as safety boots, hi-vis, eye and hearing protection
- Permit-to-work and lockout/tagout procedures
- Incident and hazard reporting processes
- Rules on chemicals, hot work and smoking
If your site is a construction project, general construction induction requirements may apply to cleaners performing construction work. Under WA regulations, this includes cleaning and maintenance of structures under construction. However, ordinary cleaning or maintenance work at an existing site does not automatically require a general construction induction card simply because the premises are industrial.
Every person who enters the site, including cleaners working after hours, should complete the induction before they start. Your contractor will usually expect to be given the induction content and any site-specific rules at the time of quoting, not on the first night of work.
What Your Site Should Expect From an Industrial Cleaning Contractor
A professional contractor should be able to show you a clear process from enquiry to completion. Look for:
- A site inspection or detailed scoping conversation. Industrial work is difficult to quote accurately without understanding the equipment, contaminants, access and shutdown windows.
- A written scope of work. This should define what’s included, how often, and what’s excluded, such as confined spaces or specialised plant cleaning.
- Documented safety processes. This includes risk assessments, SDS and evidence of worker training. Ask which licences, high-risk work qualifications, competency records and insurance certificates are required for the specific tasks and site. Requirements depend on the equipment, work activities and contractual conditions. For example, workers operating equipment covered by high-risk work licensing requirements must hold the relevant licence, while insurance documentation should meet the site’s contractual requirements.
- Appropriate equipment. Industrial vacuums, scrubbers and degreasing tools suited to your environment.
- Scheduling that fits production. Cleaning is often planned around shutdowns, night shifts or weekends to limit disruption.
- Clear reporting. Records of what was cleaned and any hazards or maintenance issues noticed, such as leaks or damaged guarding.
If you’re unsure how to structure a scope, our services overview is a starting point for discussion.
How to Prepare Your Site Before the Clean
A little preparation makes the work safer and more efficient:
- Nominate a site contact who can authorise access, isolation and permits.
- Share your hazard information, including SDS for site chemicals, known hazard areas and any past incidents.
- Confirm shutdown windows and which equipment can be isolated.
- Clear access paths to machinery, racking and high-level areas.
- Agree on waste handling, particularly for oily rags, filter material and wash-down residue. In Western Australia, liquid waste and other specified waste categories may be classified as controlled waste under the Environmental Protection (Controlled Waste) Regulations 2004. Confirm the correct waste classification and disposal method before cleaning begins. Controlled waste transported on public roads must be handled by appropriately licensed carriers, with applicable tracking and disposal requirements. Industrial wash water and contaminated cleaning residues must be directed to an authorised disposal or wastewater system rather than discharged into stormwater drains or the environment.
Choosing a Provider in Perth’s Industrial Areas
Perth’s industrial precincts, including areas such as Kewdale, Jandakot and Welshpool, have their own access rules and site conditions. Local knowledge helps with logistics and response times. You can see one of the locations we cover on our commercial cleaning in Kewdale page.
When comparing providers, prioritise experience with similar sites, a clear safety approach and transparent scoping over the lowest quote. Industrial cleaning that skips safety steps or doesn’t suit your contaminants can leave you with greater risk, not less.
If you’d like to discuss your site, contact our team with details of your facility, the type of cleaning required and your preferred timing.
FAQ
How often should industrial cleaning be carried out?
It depends on your process, the type of contamination and your risk assessment. Some sites need daily cleaning of floors and high-traffic areas, with periodic deep cleans of machinery and overhead surfaces. A site inspection is the best way to set a suitable schedule.
Can machinery be cleaned while it is operating?
Generally, cleaning around moving or energised equipment requires isolation and lockout first. Your site’s procedures and the equipment manufacturer’s guidance determine what is permitted.
Do cleaners need a site induction?
Yes, in most industrial workplaces. The site operator normally delivers it, and it should be completed before work begins. Site-specific induction requirements depend on the workplace, the activities being undertaken and the hazards workers may encounter. The person conducting a business or undertaking must provide workers with suitable information, instruction, training and supervision for the work and associated risks.
Is dust extraction different from regular vacuuming?
Yes. Industrial dust control uses vacuums built for heavy loads and suitable filtration, and follows methods that avoid spreading fine dust back into the air.
What information do I need to provide for a quote?
Provide the site address, floor area, type of operation, equipment to be cleaned, known hazards, access restrictions and preferred cleaning times. Photos or a site walk-through help the contractor scope accurately.

